PCB Assembly Cost in China: What You Actually Pay
Two different numbers get quoted for the same project, and mixing them up is the most expensive mistake in the process. Bare PCB fabrication is the cheap half: a panelized prototype order starts around ¥20 (about $3), and small batches come in at roughly ¥1,309 for 50 boards or ¥4,905 for 300 — about ¥16–26 a board. PCBA, the assembly service that mounts the components, has no fixed tier at all: it is quoted from part count, solder joints, stencil and engineering fee, and commonly lands between a few hundred and a few thousand yuan per board. Below: what each number covers, how long each stage really takes, and the three files nobody can quote without.
Need real numbers? Request quotes through our sourcing team — we collect quotes from several Shenzhen assemblers for the same files so you can compare.
Runs entirely in your browser — nothing you type here is uploaded or stored. This is a rough planning estimate based on published 2025 price ranges for Chinese prototype and low-volume assembly, with rule-of-thumb adjustments for board size, layer count and turnaround. Components, stencils, shipping and import duties are not included. It is not a quote.
Two quotes, not one
Ask for "the PCB price" and you will get two different answers from two suppliers, because the industry quotes two separate things. Bare PCB fabrication covers the board itself: copper, soldermask, silkscreen, surface finish, drilled and routed. PCBA covers what goes on top: paste, placement, reflow, and — if you order turnkey — the components themselves.
The gap between them is large enough that a misunderstanding here can sink a budget. A bare board is a commodity priced by area and layer count; assembly is a service priced by how many parts you put on it. Quoting one and budgeting for the other is the single most common way a prototype order goes wrong.
| What is being quoted | Typical number | What drives it |
|---|---|---|
| Bare PCB, panelized prototype | From about ¥20 | Panel sharing with other orders; a dedicated single-board tooling run used to cost ¥500–800 and still does when you insist on one |
| Bare PCB, small batch | ≈¥1,309 for 50 boards, ≈¥4,905 for 300 | Layer count, board area, panel utilization — this is the ¥16–26 a board range |
| PCBA, assembly only | A few hundred to a few thousand yuan a board | Part count, solder joints, stencil, engineering fee — no fixed tier exists |
Figures above are the quotes local houses give in yuan; the dollar amounts are approximations at roughly ¥7 to the dollar. Assembly numbers exclude components unless the order is turnkey.
Lead times: board type decides the fabrication clock, availability decides the assembly one
Fabrication runs on a predictable ladder, and it is the cleanest number in the whole process: single- and double-sided boards turn in about 24 hours, four-layer boards in about 48, and six- to eight-layer boards in about 72. The condition attached to all three is that the files pass CAM review the first time and the process is standard — a non-standard surface finish, an unusual stackup or an impedance requirement moves you off the ladder.
Assembly is a different kind of wait, because it depends on parts. With files complete and components in hand, a straightforward SMT run can be built in about eight hours. The real timeline is usually set upstream: sourcing components commonly takes around three days, and then shipping adds its own time on top. End to end, a whole PCBA order lands at eight days or more far more often than the eight-hour build time suggests.
Which is why the useful question is not "how fast can you do it" but "when does the clock start". Ask it explicitly: from file receipt, from DFM sign-off, from components arriving, or from payment. Two suppliers quoting 24 hours can be ten days apart on your desk.
Why the per-board number moves so much
At low volume the per-board price is dominated by setup rather than materials. Machine programming, a stencil, and line changeover get spread across however many boards you order, which is why ten boards can cost several times the per-unit price of a thousand. This is also why low-volume assembly quotes legitimately look expensive next to high-volume ones — nothing has been marked up, the fixed costs simply have fewer boards to land on.
Shenzhen's advantage is structural rather than promotional: the component markets, stencil shops and board fabricators sit within a short drive of each other, so a change in the BOM does not restart the logistics. That density is why short fabrication turns are a standard product here rather than a favour.
What you need before you can get a quote
Three files decide everything:
- Gerber files (RS-274X) — the board fabricator's input: copper layers, soldermask, silkscreen, drill. This is all a bare-board quote needs.
- BOM (bill of materials) — every component with manufacturer part numbers, quantities and reference designators. Vague entries ('10k resistor, 0402, any brand') are where quotes and reality drift apart.
- Pick-and-place / centroid file — the X/Y coordinates and rotation for every part, which drives the machine program and the assembly quote.
Decide also between turnkey (the assembler sources and fits every component — the default for prototypes) and consignment (you ship your own parts to the line). Consignment saves component margin but adds shipping, customs and inventory risk; for prototype runs most teams go turnkey and keep the BOM clean.
If the part that slows you down is hesitation about sending the design itself, our guide to sending Gerber, BOM and drawings to a Chinese supplier covers what a first quote really needs and how experienced buyers sequence files, NDAs and payments.
Mistakes that delay quotes and boards
Most slow first orders trace back to the files, not the factory. BOM lines without manufacturer part numbers force the assembler to guess and wait for your confirmation. Centroid files missing rotation or using a different reference origin than the Gerbers stall the CAM review. Mechanical fit parts — connectors, enclosures, displays — quoted without a datasheet link get substituted with whatever is in the local market, which is sometimes better and sometimes not what your enclosure expected. Clean up those three before sending files out, and the first quote arrives in days instead of weeks.
From estimate to real quotes
The estimator on this page uses these ranges plus stated rule-of-thumb adjustments, which makes it honest but rough. Real quotes differ by house, by component market prices on the day, and by yield assumptions. Two habits make the comparison meaningful: state up front whether you want a bare board or a turnkey PCBA, and ask what each lead time is counted from. Then send the same three files to several assemblers and compare the line items rather than the total — a China sourcing agent does exactly that on the ground, and our factory tours let you walk the line before you commit a production order.
PCB assembly in China FAQ
How much does PCB assembly in China cost per board?
It depends which half of the order you mean, and this is where most quotes get misread. Bare PCB fabrication is inexpensive: a panelized prototype run starts around ¥20 (about $3), and small batches run roughly ¥1,309 for 50 boards or ¥4,905 for 300 — about ¥16–26 a board. PCBA, the service that mounts components, has no fixed tier: houses quote from part count, solder joints, stencil and engineering fee, and a typical figure is a few hundred to a few thousand yuan per board. Always ask for the two lines separately.
Is there a minimum order for PCB assembly in China?
Physical minimums are small — one to five boards for a prototype — but the charges around them are not. Setup, stencil and handling fees set a floor on a small order, so the per-board price on ten boards can be many times the price on a thousand. Ask for the setup, stencil and engineering lines itemised before you compare two quotes, because a house with a low unit price and a large engineering fee is often the more expensive option at prototype volume.
How long does PCB fabrication and assembly take?
Bare boards: 24 hours for single- and double-sided, 48 hours for four layers, 72 hours for six to eight layers — assuming the files pass CAM review first time and the process is standard. The assembly side runs differently: once your files and parts are in hand, a straightforward SMT run can be built in about eight hours. A whole PCBA order adds component purchasing, usually around three days, plus logistics, so eight days or more is realistic end to end. Ask which date the clock starts from.
Do Chinese assemblers source the components too?
Yes — turnkey assembly is the default for prototypes, with the house sourcing components from local markets and distributors against your BOM. Consignment (you supply parts) is possible but adds logistics. Watch for BOM lines without manufacturer part numbers: they are where component substitutions quietly happen.